Thermodynamics Research Center / ThermoML | Journal of Chemical and Engineering Data

Temperature Dependence Measurements of the Density at 0.1 MPa for 1-Alkyl-3-methylimidazolium-Based Ionic Liquids with the Trifluoromethanesulfonate and Tetrafluoroborate Anion

Klomfar, J.[Jaroslav], Souckova, M.[Monika], Patek, J.[Jaroslav]
J. Chem. Eng. Data 2010, 55, 9, 4054-4057
ABSTRACT
Experimental density data are reported for four 1-Cn-3-methylimidazolium-based ionic liquids (n = 2, 4, 6), three with trifluoromethanesulfonate and one with a tetrafluoroborate anion, at atmospheric pressure and at temperatures in the range of (268 to 356) K. The buoyancy method was employed, using the microbalance of the Krss K100MK2 tensiometer. At each nominal temperature 40 evaluated buoyancy and temperature readings in two runs were taken in most cases. Averages of density and temperature values obtained at the individual nominal temperatures are presented with an estimated total standard uncertainty less than 0.3 kg*m-3 (2.5*10-4 ?) and 0.02 K, respectively. The 83 new experimental data points on the density-temperature relation of the four ionic liquids of interest are means calculated from about 3000 individual density readings, which have been altogether taken in the present study. Measurements on two samples of the same stated high purity from different suppliers were performed for two ionic liquids, to demonstrate the influence of the sample origin.
Compounds
# Formula Name
1 C7H11F3N2O3S 1-ethyl-3-methylimidazolium trifluoromethanesulfonate
2 C9H15F3N2O3S 1-butyl-3-methylimidazolium trifluoromethanesulfonate
3 C11H19F3N2O3S 1-hexyl-3-methylimidazolium trifluoromethanesulfonate
4 C10H19BF4N2 1-hexyl-3-methylimidazolium tetrafluoroborate
5 H2O water
Datasets
The table above is generated from the ThermoML associated json file (link above). POMD and RXND refer to PureOrMixture and Reaction Datasets. The compound numbers are included in properties, variables, and phases, if specificied; the numbers refer to the table of compounds on the left.
Type Compound-# Property Variable Constraint Phase Method #Points
  • POMD
  • 1
  • Mass density, kg/m3 ; Liquid
  • Temperature, K; Liquid
  • Pressure, kPa; Liquid
  • Liquid
  • Buoyancy - hydrostatic balance
  • 18
  • POMD
  • 2
  • Mass density, kg/m3 ; Liquid
  • Temperature, K; Liquid
  • Pressure, kPa; Liquid
  • Liquid
  • Buoyancy - hydrostatic balance
  • 13
  • POMD
  • 2
  • Mass density, kg/m3 ; Liquid
  • Temperature, K; Liquid
  • Pressure, kPa; Liquid
  • Liquid
  • Buoyancy - hydrostatic balance
  • 13
  • POMD
  • 3
  • Mass density, kg/m3 ; Liquid
  • Temperature, K; Liquid
  • Pressure, kPa; Liquid
  • Liquid
  • Buoyancy - hydrostatic balance
  • 13
  • POMD
  • 4
  • Mass density, kg/m3 ; Liquid
  • Temperature, K; Liquid
  • Pressure, kPa; Liquid
  • Liquid
  • Buoyancy - hydrostatic balance
  • 18
  • POMD
  • 5
  • 2
  • Mass density, kg/m3 ; Liquid
  • Temperature, K; Liquid
  • Pressure, kPa; Liquid
  • Mole fraction - 5; Liquid
  • Liquid
  • Buoyancy - hydrostatic balance
  • 8