Thermodynamics Research Center / ThermoML | Journal of Chemical Thermodynamics

Phase diagrams of acetonitrile or (acetone + water + EPPS) buffer phase separation systems at 298.15 K and quantum chemical modeling

Taha, M.[Mohamed], Teng, H.-L.[Han-Lan], Lee, M. J.[Ming-Jer]
J. Chem. Thermodyn. 2012, 54, 134-141
ABSTRACT
We found that addition of 3-[4-(2-hydroxyethyl)-1-piperazinyl]propane sulfonic acid (EPPS) induces phase separation of (acetonitrile + water) mixtures and (acetone + water) mixtures at T = 298 K, although these organic solvents are miscible with water at any mixing ratio. The phase diagrams of (acetonitrile + water + EPPS) and (acetone + water + EPPS) systems showed that the phase separation takes place in a wide range of the organic solvent mass fractions, 0.25 less than w less than 0.95. The solubility limits of EPPS buffer before the phase separations were determined by densimetry. The (liquid + liquid) equilibrium (LLE) and (solid + liquid + liquid) equilibrium (SLLE) data were measured for these ternary systems at T = 298.15 K under atmospheric pressure. The EPPS can be used as an auxiliary agent to pass over the (acetonitrile + water) azeotrope. The phase boundary data of the different specific regions in the phase diagrams were fitted to an empirical equation and the effective excluded volume (EEV) model. The experimental LLE data (tie-lines) were found to be thermodynamically consistent according to Othmer-Tobias equation. The NRTL activity coefficient model was used to correlate the experimental tie-lines. Molecular mechanical and semi-empirical quantum-mechanical calculations were used to study the intermolecular interactions between EPPS buffer and acetonitrile/acetone in gas phase and in water under the periodic boundary conditions. Then, we proposed a possible mechanism of EPPS-induced phase separation of the investigated systems.
Compounds
# Formula Name
1 C9H20N2O4S 4-(2-hydroxyethyl)-1-piperazinepropanesulfonic acid
2 C2H3N acetonitrile
3 H2O water
4 C3H6O acetone
Datasets
The table above is generated from the ThermoML associated json file (link above). POMD and RXND refer to PureOrMixture and Reaction Datasets. The compound numbers are included in properties, variables, and phases, if specificied; the numbers refer to the table of compounds on the left.
Type Compound-# Property Variable Constraint Phase Method #Points
  • POMD
  • 2
  • 3
  • 1
  • Mass fraction - 3 ; Liquid mixture 2
  • Mass fraction - 2; Liquid mixture 1
  • Temperature, K; Liquid mixture 1
  • Liquid mixture 2
  • Liquid mixture 1
  • Crystal - 1
  • Density calibration data
  • 1
  • POMD
  • 2
  • 3
  • 1
  • Mass fraction - 1 ; Liquid
  • Mass fraction - 3; Liquid
  • Temperature, K; Liquid
  • Pressure, kPa; Liquid
  • Liquid
  • Crystal - 1
  • Titration method
  • 3
  • POMD
  • 2
  • 3
  • 1
  • Mass fraction - 1 ; Liquid mixture 1
  • Mass fraction - 3; Liquid mixture 1
  • Temperature, K; Liquid mixture 1
  • Pressure, kPa; Liquid mixture 1
  • Liquid mixture 1
  • Liquid mixture 2
  • Titration method
  • 7
  • POMD
  • 2
  • 3
  • 1
  • Mass fraction - 1 ; Liquid mixture 1
  • Mass fraction - 3; Liquid mixture 1
  • Temperature, K; Liquid mixture 1
  • Liquid mixture 1
  • Crystal - 1
  • Liquid mixture 2
  • Titration method
  • 11
  • POMD
  • 2
  • 3
  • 1
  • Mass density, kg/m3 ; Liquid
  • Solvent: Mass fraction - 2; Liquid
  • Molality, mol/kg - 1; Liquid
  • Temperature, K; Liquid
  • Pressure, kPa; Liquid
  • Liquid
  • Vibrating tube method
  • 14
  • POMD
  • 2
  • 3
  • 1
  • Mass fraction - 3 ; Liquid mixture 2
  • Mass fraction - 3 ; Liquid mixture 1
  • Mass fraction - 2 ; Liquid mixture 1
  • Mass fraction - 2; Liquid mixture 2
  • Temperature, K; Liquid mixture 1
  • Pressure, kPa; Liquid mixture 2
  • Liquid mixture 2
  • Liquid mixture 1
  • Density calibration data
  • Density calibration data
  • Density calibration data
  • 6
  • POMD
  • 4
  • 3
  • 1
  • Mass fraction - 3 ; Liquid mixture 2
  • Mass fraction - 4; Liquid mixture 2
  • Temperature, K; Liquid mixture 2
  • Liquid mixture 2
  • Crystal - 1
  • Liquid mixture 1
  • Density calibration data
  • 1
  • POMD
  • 4
  • 3
  • 1
  • Mass fraction - 1 ; Liquid
  • Mass fraction - 3; Liquid
  • Temperature, K; Liquid
  • Pressure, kPa; Liquid
  • Liquid
  • Crystal - 1
  • Titration method
  • 3
  • POMD
  • 4
  • 3
  • 1
  • Mass fraction - 1 ; Liquid mixture 1
  • Mass fraction - 3; Liquid mixture 1
  • Temperature, K; Liquid mixture 1
  • Pressure, kPa; Liquid mixture 1
  • Liquid mixture 1
  • Liquid mixture 2
  • Titration method
  • 8
  • POMD
  • 4
  • 3
  • 1
  • Mass fraction - 1 ; Liquid mixture 1
  • Mass fraction - 3; Liquid mixture 1
  • Temperature, K; Liquid mixture 1
  • Liquid mixture 1
  • Crystal - 1
  • Liquid mixture 2
  • Titration method
  • 8
  • POMD
  • 4
  • 3
  • 1
  • Mass density, kg/m3 ; Liquid
  • Solvent: Mass fraction - 4; Liquid
  • Molality, mol/kg - 1; Liquid
  • Temperature, K; Liquid
  • Pressure, kPa; Liquid
  • Liquid
  • Vibrating tube method
  • 14
  • POMD
  • 4
  • 3
  • 1
  • Mass fraction - 3 ; Liquid mixture 2
  • Mass fraction - 3 ; Liquid mixture 1
  • Mass fraction - 4 ; Liquid mixture 1
  • Mass fraction - 4; Liquid mixture 2
  • Temperature, K; Liquid mixture 1
  • Pressure, kPa; Liquid mixture 1
  • Liquid mixture 2
  • Liquid mixture 1
  • Density calibration data
  • Density calibration data
  • Density calibration data
  • 6